NEUTRIK®/SOMMER speakON®, 4-pole , plastic-, screw terminal w/o wire protection-female connector, silver plated contact(s), straight, max. 4 mm², grey, 50 pcs.
€11.70*
NL4FX-SOM-D
With transparent ring for subsequent, individual labelling / coding. Bulk materialMiscellaneous:Bulk goods
HICON XLR, water- and dustproof IP67 while connected , 3-pole , metal-female connector, gold plated contact(s), straight, black
€7.97*
HI-X3CF-HD-B
A true all-rounder...is the new HICON XLR connector HI-MARLIN. This connector does not only look good and lies ergonomically in the hand; due to its special design it also solves many problems an installation or event technician might be faced with.These HICON HI-MARLIN XLR connectors, which are water- and dustproof according to IP67, repel a direct water jet or infiltrating moisture and may even be put under water without impairing its function.Many new cables of the professional audio technology sector have a gas-injected foam insulation, which is why standard chuck strain reliefs are not ideal. They would squash the delicate wire insulations, thereby affecting the electrical values. Here the lamellar seal with internal grommet offers the perfect solution. The pressure of the strain relief is evenly spread over the entire cable diameter and squeezes no bumps into the jacket and insulation material. Special emphasis is placed on the locking device, which is very convenient and extremely durable. It has no long spring travels and the pressure spring-loaded mechanism is located in the locking knob instead of the contact base, as is usually the case. This also guarantees an easy and fuss-free mounting or cable assembly. These connectors are loyal companions in particularly wet situations such as the installation in leisure parks, near the coast, in ship and boat building, with outdoor festivities like Christmas markets, funfairs, skiing events, in sediment technology etc.The HICON HI-MARLIN XLR connectors are salt water and UV resistant.Advantages:No infiltration of water, dirt, moisture, sandWater- and dustproof according to IP67 while connectedVery good handling with pleasant plug-in sensationAES/EBU conform (no vibration sensor)Especially cable-protecting strain reliefHigh mating cycles due to intelligent, zero-wear locking mechanismEasy and fast assembleApplication:Installation at outdoor events, in ship and boat building, skiing events etc.Permanent connections in coastal areas
HICON XLR, water- and dustproof IP67 while connected , 3-pole , metal-male connector, gold plated contact(s), straight, black
€7.10*
HI-X3CM-HD-B
A true all-rounder...is the new HICON XLR connector HI-MARLIN. This connector does not only look good and lies ergonomically in the hand; due to its special design it also solves many problems an installation or event technician might be faced with.These HICON HI-MARLIN XLR connectors, which are water- and dustproof according to IP67, repel a direct water jet or infiltrating moisture and may even be put under water without impairing its function.Many new cables of the professional audio technology sector have a gas-injected foam insulation, which is why standard chuck strain reliefs are not ideal. They would squash the delicate wire insulations, thereby affecting the electrical values. Here the lamellar seal with internal grommet offers the perfect solution. The pressure of the strain relief is evenly spread over the entire cable diameter and squeezes no bumps into the jacket and insulation material. Special emphasis is placed on the locking device, which is very convenient and extremely durable. It has no long spring travels and the pressure spring-loaded mechanism is located in the locking knob instead of the contact base, as is usually the case. This also guarantees an easy and fuss-free mounting or cable assembly. These connectors are loyal companions in particularly wet situations such as the installation in leisure parks, near the coast, in ship and boat building, with outdoor festivities like Christmas markets, funfairs, skiing events, in sediment technology etc.The HICON HI-MARLIN XLR connectors are salt water and UV resistant.Advantages:No infiltration of water, dirt, moisture, sandWater- and dustproof according to IP67 while connectedVery good handling with pleasant plug-in sensationAES/EBU conform (no vibration sensor)Especially cable-protecting strain reliefHigh mating cycles due to intelligent, zero-wear locking mechanismEasy and fast assembleApplication:Installation at outdoor events, in ship and boat building, skiing events etc.Permanent connections in coastal areas
HICON BNC 6G-SDI screw-type-male connector, straight, Nickel-plated / black
€13.54*
BNC0.8/3.7-6G-SM
On the plug - screw down - go!Easy assembly without crimping tool!The new HICON-BNC0.8/3.7-6G-SM connector uses a new revolutionary plug system which extremely simplifies the assembly of BNC and RG cables. You no longer need an extra bulky crimping tool, but simply mount the connector by hand or with the help of two wrenches (size 12mm and 13mm) to a video cable 0.8/3.7 (e.g. SOMMER CABLE VECTOR 600-0162)! The HICON BNC connector BNC0.8/3.7-6G-SM transmits the 3G and 6G video standard.
1. Pull the end cap over the cable sheath
2. Strip the cable with a stripping tool (e.g. WAAl) or a sharp knife
3. Remove the protruding strands of the braid
ed shielding4. Push the cable into the connector up to the insulation so that the crimp foot slides under the shielding or sheath at the same time
5. Close the end cap by turning it clockwise until it clicks into position6.
Depending on the shielding coverage, the end cap can be locked by hand or with additional 12mm and 13mm wrenchesAdvantages:simple Screw & Play assembly without crimping tool even for untrained users3 micrograms hard gold plated pin for high number of mating cyclesExtremely robust metal housingSuitable for almost all 0.8/3.7 video cablesDiscreet, matt black end capColour coding possible with two stretchable colour rings of the HI-UC seriesApplication:Transmission of 3G and 6G video signalsConnection of S-PDIF devices
HICON crimp-male connector, straight, nickel
€8.31*
BNC1.2/5.0-6G
The BNC connector (Bayonet Neill Concelman) is one of the best-known coaxial connectors and was invented at the end of the 1940s. It is available with 50 or 75 Ω characteristic impedance and is primarily used in radio, video, medical and computer technology. Our connectors fulfil the requirements of IEC 169-8, MIL-C-39012.While RG and video connectors for the analogue sector are relatively easy to produce, the currently required 3G/6G/12G standards require high-quality, precise manufacturing technology that can produce in the lowest tolerance ranges. The corresponding machines are largely manufactured in Germany and also refine HICON connector production.
The HICON BNC-HD and 6G connectors for digital serial video transmission are among the few top class connectors on the market and are technically at the highest level. This is why they are used in numerous radio/broadcast/HDTV transmissions.
The HICON HD-SDI and 6G-SDI series not only has a gold-plated pin, but also a hard gold-plated shield housing, which keeps the skin effect as low as possible.The 6G-SDI broadcast BNC cable connector (crimp 75 Ω) has hard gold-plated contact surfaces (4 μm) and an internal thread in the pin receptacle. The housing is made of hard gold-plated, corrosion-resistant plated brass/beryllium bronze. This 2-pin, male connector is suitable for SC-Vector Plus 1.2L/5.0, SC-Vector Plus 1.2L/4.8DZ, SC-Astral LLX, Transit MC3031 and Transit MC3231 cables and uses the KS1250 colour grommet.
NEUTRIK® powerCON®, UL50E , 3-pole , plastic-female connector, straight, max. 2,5 mm², black
€17.60*
NAC3PX-TOP
Power outlet / power inlet:- 3-pole chassis socket + connector
HICON XLR, Waterproof and dustproof to IP54 while connected , 3-pole , Polyamide-female connector, gold plated contact(s), straight, black
€7.10*
HI-X3DF-HD-B
A true all-rounder...Is the new HI-MARLIN XLR connector from HICON. Not only does it look good and lies ergonomically in your hand - due to its special construction, it also solves many problems installation or event technicians are faced with. A lot of new cables in professional audio engineering are gas-injected which is why standard chuck strain reliefs are not ideal. They crush the sensitive wire insulations and thereby affect the electrical values. Here the lamellar seal with inside rubber gasket is the perfect solution. The pressure from the strain relief is evenly distributed over the entire cable diameter and presses no dips into the jacket and insulation material. We paid special attention to the locking mechanism which is very compact and extremely durable. It has no long spring travels and the pressure suspension is located in the locking knob and not – as otherwise usual – in the contact carrier. This ensures a simple, no-frills assembly or cable manufacture. These connectors are faithful companions especially in wet environments such as the installation in amusement parks, in coastal areas, in ship and boat building, at outdoor festivities like Christmas markets, funfairs, skiing events, in sediment technology, etc. The HICON HI-MARLIN XLR connectors are saltwater and UV resistant.Protection only applies when plugged inAdvantages:No infiltration of water, dirt, moisture, sandWaterproof and dustproof to IP54 while connectedVery good handling with pleasant plug-in sensationAES/EBU conform (no vibration sensor)Especially cable-protecting strain reliefHigh mating cycles due to intelligent, zero-wear locking mechanismEasy and fast assembleApplication:Installation at outdoor events, in ship and boat building, skiing events etc.Permanent connections in coastal areas
HICON BNC crimp-male connector, straight, nickel
€7.35*
BNC0.8/3.7-6G
The BNC connector (Bayonet Neill Concelman) is one of the best-known coaxial connectors and was invented at the end of the 1940s. It is available with 50 or 75 Ω characteristic impedance and is primarily used in radio, video, medical and computer technology. Our connectors fulfil the requirements of IEC 169-8, MIL-C-39012.While RG and video connectors for the analogue sector are relatively easy to produce, the currently required 3G/6G/12G standards require high-quality, precise manufacturing technology that can produce in the lowest tolerance ranges. The corresponding machines are largely manufactured in Germany and also refine HICON connector production.
The HICON BNC-HD and 6G connectors for digital serial video transmission are among the few top class connectors on the market and are technically at the highest level. This is why they are used in numerous radio/broadcast/HDTV transmissions.
The HICON HD-SDI and 6G-SDI series not only has a gold-plated pin, but also a hard gold-plated shield housing, which keeps the skin effect as low as possible.The 6G-SDI broadcast BNC cable connector (crimp 75 Ω) with hard gold-plated contact surfaces (4 μm) and internal thread in the pin receptacle has a housing made of hard gold-plated brass/beryllium bronze with a corrosion-resistant finish and is suitable for SC-Vector 0.8/3.7, SC-Focusline PUR and Transit MC2235 cables with KS59 colour grommet.
HICON Protective cap with fastening cord for HI-FIBER4-FD
€16.30*
HI-FIBER4-FCAP
The bright spot with an overview...
The HICON HI-FIBER connector gives you that, because it fits all 4-fibre cables and, with a little practice, you can carry out repairs on site yourself. Our roadworthy HICON HI-FIBER connector system is based on 4 optical LC fibre optic cables that are protected by a robust, compact metal housing.
It consists of a cable plug and an installation socket in compact D-flange format, which can also be used as a universal cable coupling for extension (cascading). You can also use the socket to connect the HI-FIBER system with up to 4 conventional LC cables (or 2 LC duplex cables) and connect it to existing LC systems or LC/ST or LC/SC adapters - simply plug in the LC and you're done.The protective cap with fastening cable is designed for the LC coupling HI-FIBER4-FD.
NEUTRIK® powerCON®, UL50E , 3-pole , plastic-, Connector-in technology-male connector, silver plated contact(s), Type D, black
€6.90*
NAC3MPX-TOP
True 1 / 16 APower inlet: - 3-pole built-in connectorMiscellaneous:Line connector / power inlet6,35mm Flat tabs
HICON crimp-male connector, straight, nickel
€10.71*
BNC1.6/7.3-6G
The BNC connector (Bayonet Neill Concelman) is one of the best-known coaxial connectors and was invented at the end of the 1940s. It is available with 50 or 75 Ω characteristic impedance and is primarily used in radio, video, medical and computer technology. Our connectors fulfil the requirements of IEC 169-8, MIL-C-39012.While RG and video connectors for the analogue sector are relatively easy to produce, the currently required 3G/6G/12G standards require high-quality, precise manufacturing technology that can produce in the lowest tolerance ranges. The corresponding machines are largely manufactured in Germany and also refine HICON connector production.
The HICON BNC-HD and 6G connectors for digital serial video transmission are among the few top class connectors on the market and are technically at the highest level. This is why they are used in numerous radio/broadcast/HDTV transmissions.
The HICON HD-SDI and 6G-SDI series not only has a gold-plated pin, but also a hard gold-plated shield housing, which keeps the skin effect as low as possible.The 6G-SDI broadcast BNC cable connector (crimp 75 Ω) with hard gold-plated contact surfaces (4 μm) and internal thread in the pin receptacle has a housing made of hard gold-plated brass/beryllium bronze with a corrosion-resistant finish. This 2-pin, male connector is suitable for SC-Vector Plus 1.6L/7.3 and SC-Vector Plus 1.6/7.0 cables and uses the KS1673 colour grommet. The appropriate tool for processing is the HT-CRIMPSET.
HICON XLR, Water- and dust-proof IP54 in mated condition , 3-pole , Polyamide-male connector, gold plated contact(s), straight, black
€7.90*
HI-X3DM-HD-B
A true all-rounder...Is the new HI-MARLIN XLR connector from HICON. Not only does it look good and lies ergonomically in your hand - due to its special construction, it also solves many problems installation or event technicians are faced with. A lot of new cables in professional audio engineering are gas-injected which is why standard chuck strain reliefs are not ideal. They crush the sensitive wire insulations and thereby affect the electrical values. Here the lamellar seal with inside rubber gasket is the perfect solution. The pressure from the strain relief is evenly distributed over the entire cable diameter and presses no dips into the jacket and insulation material. We paid special attention to the locking mechanism which is very compact and extremely durable. It has no long spring travels and the pressure suspension is located in the locking knob and not – as otherwise usual – in the contact carrier. This ensures a simple, no-frills assembly or cable manufacture. These connectors are faithful companions especially in wet environments such as the installation in amusement parks, in coastal areas, in ship and boat building, at outdoor festivities like Christmas markets, funfairs, skiing events, in sediment technology, etc. The HICON HI-MARLIN XLR connectors are saltwater and UV resistant.Protection only applies when plugged inAdvantages:No infiltration of water, dirt, moisture, sandWaterproof and dustproof to IP54 while connectedVery good handling with pleasant plug-in sensationAES/EBU conform (no vibration sensor)Especially cable-protecting strain reliefHigh mating cycles due to intelligent, zero-wear locking mechanismEasy and fast assembleMiscellaneous:Protective cap includedApplication:Installation at outdoor events, in ship and boat building, skiing events etc.Permanent connections in coastal areas
HICON BNC 3G-SDI crimp-female connector, thread 1/2", silver
€20.35*
BNC1.2/5.0FEH
The BNC connector (Bayonet Neill Concelman) is one of the best-known coaxial connectors and was invented at the end of the 1940s. It is available with 50 or 75 Ω characteristic impedance and is primarily used in radio, video, medical and computer technology. Our connectors fulfil the requirements of IEC 169-8, MIL-C-39012.While RG and video connectors for the analogue sector are relatively easy to produce, the currently required 3G/6G/12G standards require high-quality, precise manufacturing technology that can produce in the lowest tolerance ranges. The corresponding machines are largely manufactured in Germany and also refine HICON connector production.
The HICON BNC-HD and 6G connectors for digital serial video transmission are among the few top class connectors on the market and are technically at the highest level. This is why they are used in numerous radio/broadcast/HDTV transmissions.
The HICON HD-SDI and 6G-SDI series not only has a gold-plated pin, but also a hard gold-plated shield housing, which keeps the skin effect as low as possible.The HD-SDI/3G-SDI broadcast BNC panel jack (crimp 75 Ω) has hard gold-plated contact surfaces (4 μm) and an internal thread in the pin receptacle. The housing is made of hard gold-plated brass/beryllium bronze and has a corrosion-resistant finish. This 2-pin female connector is ground-insulated and suitable for SC-Vector Plus 1.2/5.0, SC-Vector Plus 1.2/4.8DZ, SC-Astral LLX as well as Transit MC3031 and Transit MC3231 cables without colour coding.
HICON BNC 3G-SDI crimp-female connector, Type D M3, gold
€24.73*
BNC1.2/5.0FDH
The BNC connector (Bayonet Neill Concelman) is one of the best-known coaxial connectors and was invented at the end of the 1940s. It is available with 50 or 75 Ω characteristic impedance and is primarily used in radio, video, medical and computer technology. Our connectors fulfil the requirements of IEC 169-8, MIL-C-39012.While RG and video connectors for the analogue sector are relatively easy to produce, the currently required 3G/6G/12G standards require high-quality, precise manufacturing technology that can produce in the lowest tolerance ranges. The corresponding machines are largely manufactured in Germany and also refine HICON connector production.
The HICON BNC-HD and 6G connectors for digital serial video transmission are among the few top class connectors on the market and are technically at the highest level. This is why they are used in numerous radio/broadcast/HDTV transmissions.
The HICON HD-SDI and 6G-SDI series not only has a gold-plated pin, but also a hard gold-plated shield housing, which keeps the skin effect as low as possible.The HD-SDI/3G-SDI broadcast BNC panel jack (crimp 75 Ω) has hard gold-plated contact surfaces (4 μm) and an internal thread in the pin receptacle. The housing is made of hard gold-plated brass/beryllium bronze and has a corrosion-resistant finish. This 2-pin female connector is ground-insulated and suitable for SC-Vector Plus 1.2/5.0, SC-Vector Plus 1.2/4.8DZ, SC-Astral LLX as well as Transit MC3031 and Transit MC3231 cables without colour coding.
NEUTRIK® powerCON®, UL50E , 3-pole , plastic-, Connector-in technology-male connector, silver plated contact(s), black
€12.20*
NAC3FPX-TOP
Miscellaneous:Line connector / power outlet6,35mm Flat tabs
NEUTRIK® powerCON®, IP65 in mated condition , 3-pole , plastic-, screw-type-male connector, silver plated contact(s), straight, black
€14.20*
NAC3MX-W-TOP-L
Voltage and reception power inlet:True 1 / 16A 3-pin cable connector
RJ45 CAT.6a, IDC-female connector, Keystone Clip-In, grey, 1 pc.
€6.10*
RJ45CFXL-P1
This new and very upscale CAT6A RJ-45 Keystone module is made for tool-free installation and meets all the requirements for structured communication networks pursuant to Cat. 6A Re-Embedded and Class EA (500 MHz, 10GE, in accordance with ISO/IEC 11801:2002 AM2). Owing to the large range of possible wire cross-sections, the module can be used with almost all CAT cables. Since certified products are demanded in more and more installation situations, we've had the module taken up into the GHMT Verification Program – which guarantees you the highest possible quality standard. The module is available either as a practical set of 8 or as single units.Advantages:suitable for AWG26/1 - AWG22/1, AWG27/7-AWG22/7very short designsuitable for POE+tool-free assemblyincl. dust protection cap & cable binderMiscellaneous:recommended cable: SC-Mercator CAT.7 / CAT.7a
HICON Crimping pliers tool kit w. case for BNC crimping connectors
€177.08*
HT-CRIMPSET
Coax crimping pliers tool kit in casecontaining the following parts:1 x Crimping pliers for quick-change jaws +5 x Jaw set for BNC crimping connectors:1. RG58, RG1742. RG58, RG59, RG62, RG174, RG1403. RG174, RG178, RG1794. RG8, RG9, RG11, RG174, RG3165. RG58, RG174, SMA, SMBComplete with stripping tool and case for pliers & jaw sets.
HICON XLR, water- and dustproof IP67 while connected , 3-pole , metal-female connector, silver plated contact(s), straight, nickel
€7.07*
HI-X3CF-HD
A true all-rounder...is the new HICON XLR connector HI-MARLIN. This connector does not only look good and lies ergonomically in the hand; due to its special design it also solves many problems an installation or event technician might be faced with.These HICON HI-MARLIN XLR connectors, which are water- and dustproof according to IP67, repel a direct water jet or infiltrating moisture and may even be put under water without impairing its function.Many new cables of the professional audio technology sector have a gas-injected foam insulation, which is why standard chuck strain reliefs are not ideal. They would squash the delicate wire insulations, thereby affecting the electrical values. Here the lamellar seal with internal grommet offers the perfect solution. The pressure of the strain relief is evenly spread over the entire cable diameter and squeezes no bumps into the jacket and insulation material. Special emphasis is placed on the locking device, which is very convenient and extremely durable. It has no long spring travels and the pressure spring-loaded mechanism is located in the locking knob instead of the contact base, as is usually the case. This also guarantees an easy and fuss-free mounting or cable assembly. These connectors are loyal companions in particularly wet situations such as the installation in leisure parks, near the coast, in ship and boat building, with outdoor festivities like Christmas markets, funfairs, skiing events, in sediment technology etc.The HICON HI-MARLIN XLR connectors are salt water and UV resistant.Advantages:No infiltration of water, dirt, moisture, sandWater- and dustproof according to IP67 while connectedVery good handling with pleasant plug-in sensationAES/EBU conform (no vibration sensor)Especially cable-protecting strain reliefHigh mating cycles due to intelligent, zero-wear locking mechanismEasy and fast assembleApplication:Installation at outdoor events, in ship and boat building, skiing events etc.Permanent connections in coastal areas
NEUTRIK® speakON®, 4-pole , plastic-, 3/16" Flat tabs-male connector, silver plated contact(s), Type G round, black
€6.00*
NL4MPRXX
Miscellaneous:Discontinued item, follow-up product: NL4MPRXX
HICON BNC 3G-SDI crimp-female connector, ground isolated, Type D M3, gold
€19.21*
BNC0.8/3.7FDH
The BNC connector (Bayonet Neill Concelman) is one of the best-known coaxial connectors and was invented at the end of the 1940s. It is available with 50 or 75 Ω characteristic impedance and is primarily used in radio, video, medical and computer technology. Our connectors fulfil the requirements of IEC 169-8, MIL-C-39012.While RG and video connectors for the analogue sector are relatively easy to produce, the currently required 3G/6G/12G standards require high-quality, precise manufacturing technology that can produce in the lowest tolerance ranges. The corresponding machines are largely manufactured in Germany and also refine HICON connector production.
The HICON BNC-HD and 6G connectors for digital serial video transmission are among the few top class connectors on the market and are technically at the highest level. This is why they are used in numerous radio/broadcast/HDTV transmissions.
The HICON HD-SDI and 6G-SDI series not only has a gold-plated pin, but also a hard gold-plated shield housing, which keeps the skin effect as low as possible.The HD-SDI/3G-SDI broadcast BNC panel jack (crimp 75 Ω) has hard gold-plated contact surfaces (4 μm) and an internal thread in the pin receptacle. The housing is made of hard gold-plated brass/beryllium bronze and has a corrosion-resistant finish. This 2-pin female connector is ground-insulated and is suitable for SC-Vector 0.8/3.7 cables.