Miscellaneous:incl. 1.5m AC cable, Euro plugApplication:1 x USB-C PD3.0 (max. 65W)1 x USB-C PD3.0 (max. 20W)2 x USB-A QC (je max. 18W)Input voltage: 100-240V AC 50/60Hz, 2A max. IEC C8 chassis connectorSupported charging standards: USB-C: PPS 3.3-11V-5A, QC3.0, AFC, FCP, SCP, PD3.0USB-A: Apple 5V2.4A, BC1.2, QC3.0/QC2.0, AFC, FCP, SCP, MTK

ACTIVE 19“-SYSBOXX-SYSTEME SERIES DVM194Compared with the 120 series, this is a ¼-19“ module (3 WU) for integration into the SYSBOXX housing system. Here our customers' and users' wishes were clearly paramount. For in the commercial sector it's not always easy to find the right devices for integration. Moreover, they should be easy and intuitive to operate – as specialists aren't always available for these tasks. Another important aspect is the compact integration into furniture or racks as the connections aren't always in the right place. The combination of SYSBOXX standard components with the new DVM 194 series provides a previously unknown flexibility and clarity because device and cabling system can be combined in one unit.DVM 194 MIX – The marvellous mini mixerThe dual mix-bus design allows a high degree of flexibility. Thus every input signal can be mixed individually with the two mix buses. The two microphone inputs are fitted with switchable phantom power and a switchable high-pass filter (on the back via DIP switch – only to be set by “specialists”). A tone control is available on the front for quickly changing the sound. The inputs have Euroblock terminals (3.5 mm contact spacing). The double LED display per channel (–20/0 dB) provides an easy level control.The two stereo line inputs can be fed in on the rear via RCA sockets. Input 2 has a switched mini jack sockets on the front – ideal for connecting an MP3 player. Spindle potentiometers are available on the back as gain controls for the microphone and line inputs. Above the level controls, the overall level is displayed for each mix bus via an 8-segment LED bargraph (–30, –24, –18, –12, –6, 0, +6, +12 dB). The output signals of mix bus A are fed to male 3-pole XLR sockets and those of mix bus B to Euroblock terminals. Power is provided by the appropriate 24 VDC, 4-pin XLR (15 VA) power supply DVM-194-PS.Advantages:Perfect integration into the SYSBOXX system - hence connection technology and device in one frameworkSuper high-grade components for daily use in the commercial and conference sectorIntuitve, easy operational concept - very suitable for untrained usersUltracompact design ¼-19“ x 2 HE (B x H x T): 106,5 x 84 x 128 mmPractical featuresApplication:Schools, auditoriums or public buildingsConference technology for all claimsStudio-/Live application

Connection cable to link a passive pushbutton module (e.g. W45A-5510, W45S-1010, W45W-3410, W50M-2210, W50W-4410 or SYC1-3410) to the CARDINAL DVM-194-CON media controller.4pol EUROBLOCK Buchse RM3.5 -> 3pol EUROBLOCK Buchse RM3.5PIN 1 -> PIN 1 (SWITCH)PIN 2+3 -> PIN 3 (+12V)PIN 4 -> PIN 2 (LED CATHODEConfiguration: 1 x Cardboard packaging for blister hooks, Design Sommer cable

Small, but powerful!Although less than one litre in volume, our mini high-performance amplifier boasts two channels of 100 watts into 4 ohms each (50 W @ 8 Ω). Its state-of-the-art class D power blocks with passive cooling make sure that it will always keep a cool head. The DVM-194-AMP has an intuitive menu control incl. a high-resolution display. Moreover, the device is fully remote-controllable (standby/operation, DSP functions) and, via LAN interface, allows to monitor the operation status (temperature, clip etc.). The built-in DSP provides you with an input mixer, 5 fully parametric filters (incl. high- and low-pass function), a delay plus a level control for each output channel.Both channels of the input and output sections are equipped with EUROBLOCK connections. Optionally the 2-channel transformer unit DVM-194-100V is available. The ins and outs are realised via 5.0 mm EUROBLOCK connectors.The DVM-194-AMP offers the full scope of functions, the DVM-194-AMP-LITE only has level and muting controls as well as the remotecontrolled standby function.Advantages:Perfect integration into the SYSBOXX system - hence connection technology and device in one frameworkSuper high-grade components for daily use in the commercial and conference sectorIntuitve, easy operational concept - very suitable for untrained usersUltracompact design ¼-19“ x 2 HE (B x H x T): 106,5 x 84 x 128 mmPractical featuresApplication:Schools, auditoriums or public buildingsConference technology for all claimsStudio-/Live application

The power amp managerModern power amplifiers deliver insane output power specs in the smallest possible enclosures and are more and more often equipped with digital AES3 connections. However, AES/EBU signals cannot be split as easily as analog audio signals – a simple parallel wiring of several terminals is not covered by the AES3 standard and will mostly cause problems. But due to their compact enclosure size, modern power amplifiers often have no AES3 outputs for slaving the signal through to other devices. The DVM-194-AES-NS solves just this issue! The two front AES/EBU inputs are split onto three electrically fully isolated and buffered outputs, to save you from worries and losses. The additional built-in 5-port network hub also makes the network control for the amplifiers in the amprack a cakewalk. Gone are the times when you still had to install an extra hub in your amprack and wire it error-prone “on the fly”! This is all nicely packed in an ultra compact DVM-194 slide-in module for the SYSBOXX ... Also the perfect solution for any modern power amp connection panel!Advantages:2-channel AES/EBU splitter with a max. sampling rate of 192kHzetherCON® connections for network signalsBuilt-in wide-range power

For the installation in desk, wall and floor systems the compact DVM-194-HDBT-T front panel solution comprises the following requirements in a single junction box of only three width units: HDMI®, VGA and mini jack inputs, automatic or manual source switching, HDBaseT output, power supply via PoH (Power over HDBaseT), built-in IR receiver, rear RS232 connection plus ample signal indicators.Advantages:Compatible with SYSBOXX / SYSDESK / SYSBOARD / SYSFLOOR / SYSTRUNKintegrated scaler for VGAApplication:transmits FullHD signals up to 70mtransmits 4K / UHD signals up to 40mtransmits RS232 & IR bidirectionallysupports HDCP up to V1.4

Crossover link cable for connecting the DVM-TAST-PSU system power supply to third-party devices like e.g. DVM-HDBT-SCAL52N, DVM-HDBT-MAT44, DVM-HDBT-M-F16 3-pole EUROBLOCK terminal RM3.5 -> 3-pole EUROBLOCK terminal RM3.5PIN 1 -> PIN 3 (TX->RX) PIN 2 -> PIN 1 (RX->TX) PIN 3 -> PIN 2 (GROUND)Configuration: 1 x Cardboard packaging for blister hooks, Design Sommer cable

For the installation in desk, wall and floor systems the compact DVM-194-HDBT-T front panel solution comprises the following requirements in a single junction box of only three width units: HDMI®, VGA and mini jack inputs, automatic or manual source switching, HDBaseT output, power supply via PoH (Power over HDBaseT), built-in IR receiver, rear RS232 connection plus ample signal indicators.Advantages:Compatible with SYSBOXX / SYSDESK / SYSBOARD / SYSFLOOR / SYSTRUNKintegrated scaler for VGAApplication:transmits FullHD signals up to 70mtransmits 4K / UHD signals up to 40mtransmits RS232 & IR bidirectionallysupports HDCP up to V1.4

This mixer combines the functionality of an absolutely high-fidelity stereo sub mixer – for the various sound sources on stage or in the studio – with the remote controllability of the master level via a standard swell pedal. This offers the perfect dynamics control in any situation. There are 4 stereo channels one of which also offers a parallel front panel input for the fast hook-up of an additional source (stage keyboard or e.g. MP3 player). The Master section offers individual level controls for the Main OUT, the Mono OUT and the Headphones OUT as well. Furthermore, the latter two outputs may be switched to PRE-VCA via push-buttons, which allows pre-fade listening of sounds even with the Master turned fully down. The rear side features a line-level version of the headphone bus. With the DVM-194-HPA a comfortable and powerful personal monitor solution can be realised.The VCA port is used to connect a common swell pedal (like e.g. Yamaha FC-7). The factory setting for this port covers a control range of –80 to +10 dB (at 0 dB output level). Using the optional DVM-194-DIS display unit (display) you have a permanent visual control of the swell pedal position.The Main OUT is also available via EUROBLOCK connections to facilitate well-structured rack wirings. All outputs are electronically balanced.

For the installation in desk, wall and floor systems the compact DVM-194-HDBT-T front panel solution comprises the following requirements in a single junction box of only three width units: HDMI®, VGA and mini jack inputs, automatic or manual source switching, HDBaseT output, power supply via PoH (Power over HDBaseT), built-in IR receiver, rear RS232 connection plus ample signal indicators.Advantages:Compatible with SYSBOXX / SYSDESK / SYSBOARD / SYSFLOOR / SYSTRUNKintegrated scaler for VGAApplication:transmits FullHD signals up to 70mtransmits 4K / UHD signals up to 40mtransmits RS232 & IR bidirectionallysupports HDCP up to V1.4

DVM-194 series, 2CH 100V transformer for integration into SYSBOXX system. 2 x 60W maximum power, 1/4 "19" (3WU or 21DU) 2HU

External visual display unit for VCA stereo mixer with connection cable